Microstructure and Mechanical Properties of AA1050/AA6061/AA1050 Layered Sheet Aging-Treated after Cold Roll-Bonding

Sang-Hyeon Jo; Seong-Hee Lee

doi:10.3740/MRSK.2023.33.12.565

All Issue

2023 Vol.33, Issue 12 Preview Page

Research Paper

Microstructure and Mechanical Properties of AA1050/AA6061/AA1050 Layered Sheet Aging-Treated after Cold Roll-Bonding 냉간접합압연 후 시효처리된 AA1050/AA6061/AA1050 층상판재의 미세조직 및 기계적 성질

27 December 2023. pp. 565-571

PDF XML

Abstract

AA1050/AA6061/AA1050 layered sheet was fabricated by cold roll-bonding process and subsequently T4 and T6 aging-treated. Two commercial AA1050 sheets of 1 mm thickness and one AA6061 sheet of 2 mm thickness were stacked up so that an AA6061 sheet was located between two AA1050 sheets. After surface treatments such as degreasing and wire brushing, they were then roll-bonded to a thickness of 2 mm by cold rolling. The roll-bonded Al sheets were then processed by natural aging (T4) and artificial aging (T6) treatments. The as roll-bonded Al sheets showed a typical deformation structure, where the grains are elongated in the rolling direction. However, after the T4 and T6 aging treatments, the Al sheets had a recrystallized structure consisting of coarse grains in both the AA5052 and AA6061 regions with different grain sizes in each. In addition, the sheets showed an inhomogeneous hardness distribution in the thickness direction, with higher hardness in AA6061 than in AA1050 after the T4 and T6 age treatments. The tensile strength of the T6-treated specimen was higher than that of the T4-treated one. However, the strength-ductility balance was much better in the T4-treated specimen than the T6-treated one. The tensile properties of the Al sheets fabricated in the present study were compared with those in a previous study.

Keywords

cold roll-bonding

AA1050/AA6061/AA1050 layered sheet

age treatment

mechanical properties

microstructure

References

I. J. Polmear, Light Alloys, Metallurgy of the Light Metals, 3rd ed., p.168-184, Edward Arnold, Butterworth-heinemann Press, London, UK (1995).

Y. Genma, Y. Tsunekawa, M. Okumiya and N. Mohri, Mater. Trans., JIM, 38, 232 (1997). 10.2320/matertrans1989.38.232

K. Ohori, H. Watanabe and Y. Takeuchi, Mater. Sci. Technol., 3, 57 (1987). 10.1179/mst.1987.3.1.57

S. Guo, Y. Xu, Y. Han, J. Liu, G. Xue and H. Nagaumi, Trans. Nonferrous Met. Soc. China, 24, 2393 (2014). 10.1016/S1003-6326(14)63362-8

L. Ding, Y. Weng, S. Wu, R. E. Sansers, Z. Jia and Q. Liu, Mater. Sci. Eng., A, 651, 991 (2016). 10.1016/j.msea.2015.11.050

X. Fan, Z. He, W. Zhou and S. Yuan, J. Mater. Process. Technol., 228, 179 (2016). 10.1016/j.jmatprotec.2015.10.016

W. Chae, B. K. Kim, J. Lee and J. H. Han, Korean J. Met. Mater., 58, 703 (2020). 10.3365/KJMM.2020.58.10.703

Y. M. Kim, S. W. Choi, Y. C. Kim and C. S. Kang, Korean J. Met. Mater., 59, 582 (2021). 10.3365/KJMM.2021.59.8.582

Y. W. Kim, Y. H. Jo, Y. S. Lee, H. W. Kim and J. I. Lee, Korean J. Met. Mater., 60, 83 (2022). 10.3365/KJMM.2022.60.1.83

J. Sun, W. Du, J. Fu, K. Liu, S. Li, Z. Wang and H. Liang, J. Magnesium Alloys, 10, 2649 (2023). 10.1016/j.jma.2022.09.032

H. Delavar, A. J. Mostahsanb and H. Ibrahimc, J. Magnesium Alloys, 11, 1125 (2023). 10.1016/j.jma.2023.04.010

D. G. Altenpohl, Thechnology Applications and Environment a Profile of a Modern metal, 6th ed., p.319-394, The Aluminum Association (Arlington, USA) and The Minerals, Metals & Materials Society (Pittsburgh, USA) (1998).

H. Yan and J. G. Lenard, Mater. Sci. Eng., A, 385, 419 (2004). 10.1016/S0921-5093(04)00906-2

M. J. Ahn, H. S. You and S. H. Lee, Korean J. Mater. Res., 26, 388 (2016). 10.3740/MRSK.2016.26.7.388

J. Y. Hwang and S. H. Lee, Korean J. Mater. Res., 29, 392 (2019). 10.3740/MRSK.2019.29.6.392

S. H. Lee, Arch. Metall. Mater., 65, 1093 (2020). 10.24425/amm.2020.133223

S. H. Jo and S. H. Lee, Korean J. Mater. Res., 32, 72 (2022). 10.3740/MRSK.2022.32.2.72

S. H. Jo, B. B. Park and S. H. Lee, Korean J. Mater. Res., 32, 388 (2022).

S. H. Lee, S. H. Jo and J. Y. Jeon, Korean J. Mater. Res., 33, 11 (2023). 10.3740/MRSK.2023.33.11.439

S. H. Lee, Korean J. Met. Mater., 61, 652 (2023). 10.3365/KJMM.2023.61.9.652

J. Zhao, X. Shi, M. Liu, Z. Liu, B. Luo, K. Yu, Q. Li, J. Ran and P. Zhao, J. Alloys Compd., 970, 172525 (2024). 10.1016/j.jallcom.2023.172525

G. E. Dieter, Mechanical Metallurgy, SI Metric ed., p.189-191, McGraw-Hill Book Co., UK (1988).

Information

Publisher :Materials Research Society of Korea
Publisher(Ko) :한국재료학회
Journal Title :Korean Journal of Materials Research
Journal Title(Ko) :한국재료학회지
Volume : 33
No :12
Pages :565-571
Received Date : 2023-12-04
Revised Date : 2023-12-12
Accepted Date : 2023-12-12
DOI :https://doi.org/10.3740/MRSK.2023.33.12.565

Korean Journal of Materials Research ISSN:1225-0562(Print) 2287-7258(Online) 한국재료학회지

All Issue