All Issue

2021 Vol.31, Issue 2 Preview Page
Changes in Flexural Strength and Electrical Resistivity of Bulk Graphite According to the Viscosity of Impregnant

함침재의 점도에 따른 벌크흑연의 굽힘강도 및 전기비저항 변화

Sang-Min Lee1
,
Sang-Hye Lee2
,
Jae-Seung Roh2†
이 상민1
,
이 상혜2
,
노 재승2†
1Advanced Material Research Center, Kumoh National Institute of Technology, 61 Daehak-ro, Gumi, Gyeongbuk 39177, Republic of Korea
2School of Materials Science and Engineering, Kumoh National Institute of Technology, 61 Daehak-ro, Gumi, Gyeongbuk 39177, Republic of Korea
1금오공과대학교 신소재연구소
2금오공과대학교 신소재공학과
†Corresponding author E-Mail : jsroh@kumoh.ac.kr (J.-S. Roh, Kumoh Nat'l Institute of Technology)
February 2021. pp. 108-114
PDF XML Citation
Abstract

In the manufacturing of bulk graphite, pores produced by vaporization and discharge of volatile materials in binders during carbonization reduce the density of bulk graphite, which adversely affects the electrical conductivity, strength and mechanical properties. Therefore, an impregnation process is introduced to fill the pores and increase the density of bulk graphite. In this study, bulk graphite is prepared by varying the viscosity of the impregnant. The microstructure of bulk graphite is observed. The flexural strength and electrical resistivity are measured. As the viscosity of the impregnants decreases and the number of impregnations increases, it is shown that the number of pores decreases. The density before impregnation is 1.62 g/cm3. The density increases to 1.67 g/cm3 and porosity decreases by 18.6 % after three impregnations using 5.1 cP impregnant, resulting in the best pore-filling effect. After three times of impregnation with a viscosity of 5.1 cP, the flexural strength increases by 55.2 % and the electrical resistivity decreases by 86.76 %. This shows that a slight increase in density due to the pore-filling effect improves the properties of bulk graphite.

Keywords
bulk graphite
impregnant
viscosity
flexural strength
resistivity
References
1.
J. B. Donnet, S. J. Park and M. Brendle, Carbon, 30, 263 (1992). 10.1016/0008-6223(92)90089-F
2.
J. D. Brooks and G. H. Taylor, Chemistry and Physics of Carbon, 1st ed., p.243, P. L. Walker, Jr., M. Dekker, New York (1968).
3.
H. March, E. A. Heintz and F. Rodriguez-Reinoso, Introduction to Carbon Technologies, p.669, University of Alicante, Spain (1997).
4.
J. S. Mattson and H. B. Mark, Activated Carbon: Surface Chemistry and Adsorption from Solution, p.227, M. Dekker, New York (1971).
5.
K. Ohkita and N. Tubokawa, Carbon, 10, 631 (1972). 10.1016/0008-6223(72)90101-7
6.
J. Y. Kim, S. Y. Lee, J. H. Choi and Y. D. Park, J. Korean Ceram. Soc., 29, 396 (1992).
7.
H. J. Chung and Y. S. Lim, J. Korean Ceram. Soc., 33, 1387 (1996).
8.
G. Bhatia and R. K. Aggarwal, J. Mater. Sci., 16, 1757 (1981). 10.1007/BF00540621
9.
Y. W. Shin, The J. of thr Korean Soc. for Power Syst. Eng., 9, 143 (2005).
10.
P. D. Matzinos, J. W. Patrick and A. Walker, Carbon, 34, 639 (1996). 10.1016/0008-6223(96)00018-8
11.
H. N. Youm, K. J. Kim, J. M. Lee and Y. J. Chung, J. Korean Ceram. Soc., 30, 852 (1993).
12.
J. Wang, Microelectron. Reliab., 42, 293 (2002). 10.1016/S0026-2714(01)00231-1
13.
J. Y. Sung, S. J. Lee and P. H. Shin, Journal of the Korean Society of Machine Tool Engineers Spring Conference(Mokpo, May 2008), p.155, The Korean Society of Manufacturing Technology Engineers, Seoul (2008).
14.
Y. S. Han, H. J. Kim, Y. S. Shin, J. K. Park and J. C. Ko, J. Korean Ceram. Soc., 46, 16 (2009). 10.4191/KCERS.2009.46.1.016
15.
Y. Oguchi and J. Mori, Taikabutsu Overseas, 13, 43 (1993).
16.
S. J. Park, Carbon Material, p.68, Daeyoungsa, Seoul (2006).
17.
S. M. Lee, D. S. Kang, H. S. Kim and J. S. Roh, Carbon Lett., 16, 132 (2015). 10.5714/CL.2015.16.2.132
18.
S. M. Lee, D. S. Kang, W. S. Kim and J. S. Roh, Carbon Lett., 15, 142 (2014). 10.5714/CL.2014.15.2.142
19.
Z. Lausevic and S. Marinkovic, Carbon, 24, 575 (1986). 10.1016/0008-6223(86)90148-X
20.
Y. Yamashita and K. Ouchi, Carbon, 19, 89 (1981). 10.1016/0008-6223(81)90112-3
21.
R. Lum, C. W. Wilkins, M. Robbins, A. M. Lyons and R. P. Jones, Carbon, 21, 111 (1983). 10.1016/0008-6223(83)90165-3
22.
R. B. Mathur, S. R. Dhakate, D. K. Gupta, T. L. Dhami and R. K. Aggarwal, J. Mater. Process. Tech., 203, 184 (2008). 10.1016/j.jmatprotec.2007.10.044
Information
  • Publisher :Materials Research Society of Korea
  • Publisher(Ko) :한국재료학회
  • Journal Title :Korean Journal of Materials Research
  • Journal Title(Ko) :한국재료학회지
  • Volume : 31
  • No :2
  • Pages :108-114
  • Received Date : 2021-01-06
  • Revised Date : 2021-02-01
  • Accepted Date : 2021-02-02
  • DOI :https://doi.org/10.3740/MRSK.2021.31.2.108
Journal Informaiton Korean Journal of Materials Research Korean Journal of Materials Research
Online Submission
  • scopus
  • NRF
  • KOFST
  • crossref crossmark
  • crossref cited-by
  • crosscheck
  • open access
  • ccl
Journal Informaiton Journal Informaiton - close