All Issue

2019 Vol.29, Issue 4 Preview Page
Effect of Chemical Compositions on Microstructure and Mechanical Properties of Base Metal and HAZ of Bainitic Steel Plates

베이나이트계 후판강의 모재 및 열영향부의 미세조직과 기계적 특성에 미치는 화학 조성의 영향

Sung Kyu Cho1
,
Hyung Goun Joo1
,
Sang Yong Shin2†
조 성규1
,
주 형건1
,
신 상용2†
1Technical Research Center, Hyundai Steel Company, Dangjin, 31719, South Korea
2School of Materials Science and Engineering, University of Ulsan, Ulsan, 44610, Republic of Korea
1현대제철 기술연구소
2울산대학교 첨단소재공학부
†Corresponding author E-Mail : sshin@ulsan.ac.kr (S. Y. Shin, Ulsan Univ.)
April 2019. pp. 211-220
PDF XML Citation
Abstract

In this study, three kinds of bainitic steel plates are manufactured by varying the chemical compositions and their microstructures are analyzed. Tensile and Charpy impact tests are performed at room and low temperature to investigate the correlation between microstructure and mechanical properties. In addition, heat affected zone (HAZ) specimens are fabricated by a simulation of welding processes, and the HAZ microstructure is analyzed. The base steel that has the lowest carbon equivalent has the highest volume fraction of acicular ferrite and the lowest volume fraction of secondary phases, so the strength is the lowest and the elongation is the highest. The Mo steel has a higher volume fraction of granular bainite and more secondary phases than the base steel, so the strength is high and the elongation is low. The CrNi steel has the highest volume fraction of the secondary phases, so the strength is the highest and elongation is the lowest. The tensile properties of the steels, namely, strength and elongation, have a linear correlation with the volume fraction of secondary phases. The Mo steel has the lowest Charpy impact energy at -80 °C because of coarse granular bainite. In the Base-HAZ and Mo-HAZ specimens, the hardness increases as the volume fraction of martensite-austenite constituents increases. In the CrNi-HAZ specimen, however, hardness increases as the volume fraction of martensite and bainitic ferrite increases.

Keywords
bainitic steel plates
chemical compositions
tensile properties
charpy impact properties
heat affected zone
References
1.
D. S. Liu, Q. L. Li and T. Emi, Metall. Mater. Trans. A, 42, 1349 (2011). 10.1007/s11661-010-0458-1
2.
Y. L. Zhou, T. Jia, X. J. Zhang, Z. Y. Liu and R. D. K. Misra, Mater. Sci. Eng., A, 626, 352 (2015). 10.1016/j.msea.2014.12.074
3.
B. L. Bramfitt and J. G. Speer, Metall. Trans. A, 21, 817 (1990). 10.1007/BF02656565
4.
A. D. Schino and P. E. D. Nunzio, Mater. Lett., 186, 86 (2017). 10.1016/j.matlet.2016.09.092
5.
M. Hamada, Y. Fukada and Y. Komiz, ISIJ Int., 35, 1196 (1995). 10.2355/isijinternational.35.1196
6.
S. F. Medina, ISIJ Int., 39, 930 (1999). 10.2355/isijinternational.39.930
7.
M. Chapa, ISIJ Int., 42, 1288 (2002). 10.2355/isijinternational.42.1288
8.
A. D. Schino and C. Guarnaschelli, Mater. Lett., 63, 1968 (2009). 10.1016/j.matlet.2009.06.032
9.
A. D. Schino, L. Alleva and M. Guagnelli, Mater. Sci. Forum, 860, 715 (2012). 10.4028/www.scientific.net/MSF.715-716.860
10.
C. Yu, T. C. Yang, C. Y. Huang and R. K. Shiue, Metall. Mater. Trans. A, 47A, 4777 (2016). 10.1007/s11661-016-3654-9
11.
S. K. Dhua, D. Mukerjee and D. S. Sarma, Metall. Mater. Trans. A, 32A, 2259 (2001). 10.1007/s11661-001-0201-z
12.
B. Hwang, C. G. Lee and S. J. Kim, Metall. Mater. Trans. A, 42A, 717 (2011). 10.1007/s11661-010-0448-3
13.
T. C. Yang, C. Y. Huang, T. C. Cheng, C. Yu and R. K. Shiue, Adv. Mater. Res., 936, 1312 (2014). 10.4028/www.scientific.net/AMR.936.1312
14.
G. Heigl, H. Lengauer and P. Hodnik, Steel Res. Int., 79, 931 (2008). 10.1002/srin.200806223
15.
B. C. Kim, S. Lee, N. J. Kim and D. Y. Lee, Metall. Trans. A, 22A, 139 (1991).
16.
N. Yurioka, Weld. World, 35, 375 (1995).
17.
R. E. Dolby, Weld. Res. Int., 7, 298 (1977).
18.
Y. U. Zhang, X. Li and H. Ma, Metall. Mater. Trans. B, 47, 2148 (2016). 10.1007/s11663-015-0534-4
19.
X. L. Wang, Y. T. Tsai, J. R. Yang, Z. Q. Wang, X. C. Li, C. J. Shang and R. D. K. Misra, Weld World, 61, 1155 (2017). 10.1007/s40194-017-0498-x
20.
M. Shome, O. P. Gupta, and O. N. Mohanty, Metall. Mater. Trans. A, 35A, 985 (2004). 10.1007/s11661-004-0025-8
21.
S.-C. Wang and P.-W. Kao, J. Mater. Sci., 28, 5169 (1993). 10.1007/BF00570058
22.
F. T. Han, B. C. Hwang, D. W. Suh, Z. C. Wang, D. L. Lee and S. J. Kim, Met. Mater. Int., 14, 667 (2008). 10.3365/met.mat.2008.12.667
23.
T. Araki, Atlas for Bainitic Microstructures, p. 1, ISIJ, Tokyo, Japan (1992).
24.
G. Krauss and S.W. Thompson, ISIJ Int., 35, 937 (1995). 10.2355/isijinternational.35.937
25.
H. K. D. H. Bhadeshia, Mater. Sci. Eng., A, A378, 34 (2004).
26.
D. Deng and S. Kiyoshima, Comp. Mater. Sci., 62, 23 (2012). 10.1016/j.commatsci.2012.04.037
27.
H. Qiu, M．Enoki, Y. Kawaguchi and T. Kishi, ISIJ Int., 40, 34 (2000). 10.2355/isijinternational.40.Suppl_S34
Information
  • Publisher :Materials Research Society of Korea
  • Publisher(Ko) :한국재료학회
  • Journal Title :Korean Journal of Materials Research
  • Journal Title(Ko) :한국재료학회지
  • Volume : 29
  • No :4
  • Pages :211-220
  • Received Date : 2019-02-12
  • Revised Date : 2019-03-12
  • Accepted Date : 2019-03-12
  • DOI :https://doi.org/10.3740/MRSK.2019.29.4.211
Journal Informaiton Korean Journal of Materials Research Korean Journal of Materials Research
Online Submission
  • scopus
  • NRF
  • KOFST
  • crossref crossmark
  • crossref cited-by
  • crosscheck
  • open access
  • ccl
Journal Informaiton Journal Informaiton - close